UCDS Forum

Hi.
After the update, BCM died. I updated it by choosing mondeo <2015 instead of fusion. I made ucds. Now I can not find SBL for this module and calibration files. Can anyone help you? This is the Fusion 2016 BCM number
GG9T-15604-CDB
VIN:
3FA6P0HD7GR381178

from ETIS:
SBL: DG9T-14C187-AB
ECU: FU5T-14C184-AAL

Hello, I'm throwing in such files but the dead car before the update was 16 modules now get info from vehicle sees 11 modules. Missing PSCM RCM BCM PAM PCM
The counter shines white and shows the waveform in the lower right corner and that's all

BCM
SBL: DG9T-14C187-AB
FW Parts:
1: FU5T-14C184-AAL
2: FG9T-14F389-AA
3: FG9T-14C636-BD
4: FG9T-14F390-BD
5: FG9T-14G162-CF
6: FG9T-14G163-AA
7: FU5T-14F391-AAA

now this file can be uploaded by VBL loader or can bus be the same as he chose or change to another ???

what else and what can bus pick up to upload it to bcm ???

I tried to upload but I have errors like about mine file 2 it's sounded but then the car is dead

Is it possible to bet or exchange BCM ???

what to do with such a problem ???

bolek120 писал(а):what to do with such a problem ???

Flash these files with VBF Loader... IN THIS ORDER - file order (center 14**** string) matters when flashing BCM. If out of order it will fail!
MAKE SURE SLEEP ALL MODULES IS CHECKED... DO NOT USE DEAD MODULE MODE... Keep it on Fusion 2016... DO NOT CHECK MM... May have to try HS1 and HS2 for flashing bus.

You may have to use Direct Config... Mondeo... BCM... Load from ETIS... ENTER VIN... Write to module... to write back the default as-built (only required if the flash alone does not work)

These files should work 100%... it was pulled from the as-built file from the VIN you posted. It is what came on the vehicle from the factory for BCM software.

DG9T-14C187-AB (SBL Bootloader)
FU5T-14C184-AAL
FG9T-14C636-BD
FU5T-14F391-AAA
FG9T-14F390-BD
FG9T-14F389-AA
FG9T-14G163-AA
FG9T-14G162-CF

http://www.ucdsys.ru/calibration/

bolek120 писал(а):Hello, I'm throwing in such files but the dead car before the update was 16 modules now get info from vehicle sees 11 modules. Missing PSCM RCM BCM PAM PCM
The counter shines white and shows the waveform in the lower right corner and that's all

Your original flash failed because the upgrade wizard (per your screenshot) is missing Cal config part #4 file.

Thank you for the hints !!
One more question in what order these files set in VBL ??

BCM
SBL: DG9T-14C187-AB
FW Parts:
1: FU5T-14C184-AAL
2: FG9T-14F389-AA
3: FG9T-14C636-BD
4: FG9T-14F390-BD
5: FG9T-14G162-CF
6: FG9T-14G163-AA
7: FU5T-14F391-AAA

or in such ?? Does it matter?

DG9T-14C187-AB (SBL Bootloader)
FU5T-14C184-AAL
FG9T-14C636-BD
FU5T-14F391-AAA
FG9T-14F390-BD
FG9T-14F389-AA
FG9T-14G163-AA
FG9T-14G162-CF

bolek120 писал(а):Thank you for the hints !!
One more question in what order these files set in VBL ??

BCM
SBL: DG9T-14C187-AB
FW Parts:
1: FU5T-14C184-AAL
2: FG9T-14F389-AA
3: FG9T-14C636-BD
4: FG9T-14F390-BD
5: FG9T-14G162-CF
6: FG9T-14G163-AA
7: FU5T-14F391-AAA

or in such ?? Does it matter?

DG9T-14C187-AB (SBL Bootloader)
FU5T-14C184-AAL
FG9T-14C636-BD
FU5T-14F391-AAA
FG9T-14F390-BD
FG9T-14F389-AA
FG9T-14G163-AA
FG9T-14G162-CF

Second order... yes it matters.

Hello, everything went ok BCM got up
Thanks a lot for hints and help.
I still have a question, is it possible to set the language in such a meter?
How to change it so that the mirrors and curves are illuminated ??
Change the closure of the windows ???
Can anyone tell me ??

Hello I have the same problem how did you manage that

Hello, i have same situation with 2016 Mustang 5.0
Dead bcm after flashing.
I need to know what files to upload with vbf loader, and what correct order should be.

I know just BCM software number from ETIS: GU5T-14C184-AAJ
BCM part number : GU5T-14G746-HAC

VIN: 1FA6P8CF2H5212424

Thanks for help