UCDS Forum

Module Update failed with Update Wizard; thereafter the module is no longer listed with "Get info from Vehicle" in Wizard.
V.2.0.003.001

In order to give it a second try via the VBF-File Loader (and changing download sequence for files 4 and 5 and setting CanBus HS 2 as it is suggested in a German forum, where people succeeded in overcoming the problem), I need to list the files for the update in the VBF-Loader. And here starts the trouble: I certainly have all required files in the download folder as I downloaded them before using the Upd.-Wiz, but as the Upd.-Wiz. no longer lists the IPMA-Module I don't know for sure the correct file names for the newest update. Of course, I could go back to the software-level before the failed update by using infos form the "uuw" file in the Sessions folder in order to hope that thereafter the Upd.-Wiz. again lists this module and the files required for the update, but this is a rather tedious procedure.
Can somebody list the files here?
From the uuw -file I took this section to identify the module:

<m module="IPMA">
<d DID="F10A" Desc="ECU Cal-Config Part Number" Data="DS7T-14G024-EE"/>
<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-FU5A-17E678-SC"/>
<d DID="F111" Desc="ECU Core Assembly Number" Data="DS7T-14G025-EK"/>
<d DID="F113" Desc="ECU Delivery Assembly Number" Data="DU5A-17E678-EL"/>
<d DID="F120" Desc="ECU Software #2 Part Number" Data="FT4T-14G082-HD"/>
<d DID="F162" Desc="Software Download Specification Version" Data=""/>
<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
<d DID="F16B" Desc="ECU Cal-Config #2 Part Number" Data="FT4T-14G081-HD"/>
<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="DS7T-14G019-EH"/>
</m>

This is my best guess for the VBF-Loader, based on this data and my Downloads-folder:
Problem solved: After confirming the correct files, an attempt to update via the VBF-loader failed, when it came to the 15MB-file. I loaded the 15MB-file then separatly in a second run of the VBF and it worked. Forced programming of DEAD-module was not used.

I have the same problem with the Update Wizard UCDS Adapter v3 Software v.2.0.003.001.
Module Update failed.
Later I followed the advice of @Crouser

VBF-Loader, based on this data and my Downloads-folder:

<m module="IPMA">
<d DID="F10A" Desc="ECU Cal-Config Part Number" Data="FS7T-14G024-SF"/>
<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-FU5A-17E678-SD"/>
<d DID="F111" Desc="ECU Core Assembly Number" Data="FS7T-14G025-SG"/>
<d DID="F113" Desc="ECU Delivery Assembly Number" Data="FU5A-17E678-SG"/>
<d DID="F120" Desc="ECU Software #2 Part Number" Data="FT4T-14G082-ME"/>
<d DID="F162" Desc="Software Download Specification Version" Data=""/>
<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
<d DID="F16B" Desc="ECU Cal-Config #2 Part Number" Data="FT4T-14G081-ME"/>
<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="FS7T-14G019-SG"/>
</m>
When it comes to he last 15M file is not loaded and I can not stop the procedure successfully.
It also stops blocking the file 15M.

I also tried with Ford IDS with the New Programming Module procedure, but I receive from Ford corrupt data for initial module initialization (As-Built).
Ford IDS does not even accept manual upload of AS-Built data in the IPM-A module.

Now my car is without the working IPMA module, waiting to solve somehow.

First DTC Pool
----------------------------------------
Module Name: IPMA
F10A - ECU Cal-Config Part Number : FS7T-14G024-SF -> Missing
F110 - On-line Diagnostic Database Reference Number : DS-FU5A-17E678-SD
F111 - ECU Core Assembly Number : FS7T-14G025-SG
F113 - ECU Delivery Assembly Number : FU5A-17E678-SG
F120 - ECU Software #2 Part Number : FT4T-14G082-ME
F162 - Software Download Specification Version :
F163 - Diagnostic Specification Version : 0x03
F16B - ECU Cal-Config #2 Part Number : FT4T-14G081-ME
F188 - Vehicle Manufacturer ECU Software Number : FS7T-14G019-SG -> Missing
F18C - ECU Serial Number : 0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF
----------------------------------------

After DTC Pool
----------------------------------------
Module Name: IPMA
F10A - ECU Cal-Config Part Number :
F110 - On-line Diagnostic Database Reference Number :
F111 - ECU Core Assembly Number : FS7T-14G025-SG
F113 - ECU Delivery Assembly Number : FU5A-17E678-SG
F120 - ECU Software #2 Part Number :
F162 - Software Download Specification Version : 0x05
F163 - Diagnostic Specification Version :
F16B - ECU Cal-Config #2 Part Number :
F188 - Vehicle Manufacturer ECU Software Number :
F18C - ECU Serial Number : 0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF
----------------------------------------

I can have these two calibrations?

FS7T-14G024-SF
FS7T-14G019-SG

Help help help !!!

PARTIALLY RESOLVED

I managed to unlock the IPMA module by only performing these two calibrations.
AFTER UPDATE

<m module="IPMA">
<d DID="F10A" Desc="ECU Cal-Config Part Number" Data="FS7T-14G024-SG"/> New Calibration
<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-FU5A-17E678-SE"/>
<d DID="F111" Desc="ECU Core Assembly Number" Data="FS7T-14G025-SG"/>
<d DID="F113" Desc="ECU Delivery Assembly Number" Data="FU5A-17E678-SG"/>
<d DID="F120" Desc="ECU Software #2 Part Number" Data="FT4T-14G082-ME"/>
<d DID="F162" Desc="Software Download Specification Version" Data=""/>
<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
<d DID="F16B" Desc="ECU Cal-Config #2 Part Number" Data="FT4T-14G081-ME"/>
<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="FS7T-14G019-SH"/> New Calibration

The other two calibrations do not work:

HS7T-14G082-CB
HS7T-14G081-CB

WHY ??

Pre-collision system it's OK
Traffic Sign Recognition it's OK
Lane Keeping AID error in DTC.

Camera calibration with ForScan and Ford IDS fails.

I have a suggestion that calibrations downloaded via UCDS are incorrect.


I absolutely need these two calibrations:

FS7T-14G024-SF
FS7T-14G019-SG

Hello I have 2 cameras but UCDS has an issue to write Direct Config changes to camera.
and 2nd one:
Those calibrations are not supported by UCDS and anything from DC can not be write to the module. In addition Traffic Signs Recognition does not works. Line assist is fine.

Did You manage an success update ?

I can not get into Direct Config for my IPMA and Turn on Traffic Signs Recognition. I have Line Assist and Auto High Beam which works perfectly but I want to add TSR.

Reading DC is fine. Write -> Error.

Hi

I Have a Problem with Update my IPMA. I have Update IPMA with updatewizzard.
the wizzard loads the 14G019 and 14G024 perfekt but stops with error on 14G082. and kills the module.
the i have use the VBF loader for DEAD modules
SBL / 14G019 / 14G024 / 14G081 / 14G082
it works also 14G019 / 14G024 and breaks the 100% 14G081
this was with version 2.0.003.005
now with version 2.0.003.007
i have testet the same.
whe i only load the 14G019 and 14G024
the IPMA talks with the car but the Traffic Sign / Lane Keep and Warn and the Automatic higbeam does not work.
but then i load 14G081 or 14G082 alway the system load 100% but he say Flash Fail
I have flash on HS2

My Original Software was DS7T-14G019-EJ DS7T-14G024-EF FT4T-14G081-HE FT4T-14G082-HE

My Car is an Mondeo 2015 TDCi 155KW 210HP Titanium
My Laptop is a Dell Latitude Core i7 16GB Ram 512GB SSD Win10 Enterprise 64Bit (1703)
UCDS S/N: 2A4D81BA1100000000000000000AD H/W ver.: 4.0 / F/W ver.: 11.00

How can I do to flash all and the system works 100% ?
Thanks Andy

Hi,
someone has already tried to update this IPMA module with the new version of UCDS v2.0.004.003. ??
Currently I have the module FU5A-17E678-SH with calibration FS7T-14G019SH.
UCDS Update Wizard notifies the presence of two updates.
The first update with the FUSA-17E678-SJ calibration level finds all the packages present.
while
on the second update with calibration level FUSA-17E678-SK does not find the FS7T-14G24SJ package.

Is it possible to receive it or enter it in the Calibration Server?

Good morning My module IPMA DU5A-17E678-EM after Wizard update with UCDS 2.00007.017 is dead !
I have read all topic but when I force module with Loader the installation don't work also if I separed installation, this is in photo the error, please help me ! Thx
@Diamondear where are you?????
SOLVED: OPTION WHITH "HS" ACTIVE, THX