The PSCM is dead!HELP!!!!!!

[rabbit]

Hi
UPDATE the PSCM module, then the module is dead,the car can't move now.HELP!!!!!
I would need files to work!
PSCM: CV61-3C579-GA
VIN:LVSHJCAC5EE564041



Thanks

[DanMc85]

Hi
UPDATE the PSCM module, then the module is dead,the car can't move now.HELP!!!!!
I would need files to work!
PSCM: CV61-3C579-GA
VIN:LVSHJCAC5EE564041

Thanks

CV6T-14C386-AA
CV6T-14C218-AK
CV6T-14C217-AH

Reflash these files with VBF Loader... you may have to mess with the flashing order... may have to mess with CAN bus setting... you need to add the SBL/bootloader file that was used from upgrade wizard.
Also you may have to use dead module mode and pull the power steering fuse (if you have one) and power steering module power connector from engine distribution box (if present) and plug them both back in at the same time after you hit start (most ford pscm's have two power sources)

But if this works you should be okay. If not,someone else might have more info. I am not that familiar with your vehicle.

[rabbit]

Hi
UPDATE the PSCM module, then the module is dead,the car can't move now.HELP!!!!!
I would need files to work!
PSCM: CV61-3C579-GA
VIN:LVSHJCAC5EE564041

Thanks

CV6T-14C386-AA
CV6T-14C218-AK
CV6T-14C217-AH

Reflash these files with VBF Loader... you may have to mess with the flashing order... may have to mess with CAN bus setting... you need to add the SBL/bootloader file that was used from upgrade wizard.
Also you may have to use dead module mode and pull the power steering fuse (if you have one) and power steering module power connector from engine distribution box (if present) and plug them both back in at the same time after you hit start (most ford pscm's have two power sources)

But if this works you should be okay. If not,someone else might have more info. I am not that familiar with your vehicle.

Thanks a lot . I tried, but the pscm still can't work.T_T

[rabbit]

Someone pls help me!!

[rabbit]

<m module="PSCM">
<d DID="F108" Desc="ECU Network Signal Calibration Number" Data="CV6T-14C386-AA"/>
<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-AV6C-3D070-AC"/>
<d DID="F111" Desc="ECU Core Assembly Number" Data="BV6T-14C262-AA"/>
<d DID="F113" Desc="ECU Delivery Assembly Number" Data="CV61-3C579-GA"/>
<d DID="F124" Desc="ECU Calibration Data #1 Number" Data="CV6T-14C218-AK"/>
<d DID="F162" Desc="Software Download Specification Version" Data="0x04"/>
<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="CV6T-14C217-AH"/>
</m>

[rabbit]

Flash the pscm finished with no error.

1.PNG

but the pscm module is not work .

2.PNG

The files seems all right.

730
<F108>CV6T-14C386-AA</F108>

<F111>BV6T-14C262-AA</F111>

<F113>CV61-3C579-GA</F113>

<F124>CV6T-14C218-AK</F124>

<F188>CV6T-14C217-AH</F188>

T-T pls help .

[zaqik]

I have dead module PSCM in mondeo mk5 (cable was disconnected during fw update)

SBL: DG9C-14D005-AA
F188: F1GC-14D003-AA
F10A: FG9C-14D007-NE
------------------
F113: F1GC-3F964-AA

forced programming does not work (fuse F19 has been pulled out / connected before forced programming, I tried can-bus CAN_HS and HS2):
00:00:00:503: HW/SW part number: F1GC-3F964-AA
00:00:00:505: Loading and prepare database...
00:00:09:779: Searching for SEED keys...
00:00:11:756: SEED Keys found.
00:00:39:676: Forced programming mode is started... Wait answer...
00:00:54:683: Prog Request in FORCE MODE Failed!

Do you have any idea what next? Thanks

[zaqik]

I connect UCDS direct to HS2 (connector near interior mirror) and disconnect battery - only PSCM (F19) get 12V ... module still does not respond

[Artist]

A resistor on the can bus was required to connect the module directly ...

[zaqik]

module is still in car, resistor is not needed (R=60Ohm between HS2+ and HS2-)

[DanMc85]

There are two PSCM fuses, one regular, and one large one. Disconnect them both and reconnect at same time when using dead modules mode.