Mondeo V Update Module IPMA

[Cruiser]

Module Update failed with Update Wizard; thereafter the module is no longer listed with "Get info from Vehicle" in Wizard.
V.2.0.003.001

In order to give it a second try via the VBF-File Loader (and changing download sequence for files 4 and 5 and setting CanBus HS 2 as it is suggested in a German forum, where people succeeded in overcoming the problem), I need to list the files for the update in the VBF-Loader. And here starts the trouble: I certainly have all required files in the download folder as I downloaded them before using the Upd.-Wiz, but as the Upd.-Wiz. no longer lists the IPMA-Module I don't know for sure the correct file names for the newest update. Of course, I could go back to the software-level before the failed update by using infos form the "uuw" file in the Sessions folder in order to hope that thereafter the Upd.-Wiz. again lists this module and the files required for the update, but this is a rather tedious procedure.
Can somebody list the files here?
From the uuw -file I took this section to identify the module:

<m module="IPMA">
<d DID="F10A" Desc="ECU Cal-Config Part Number" Data="DS7T-14G024-EE"/>
<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-FU5A-17E678-SC"/>
<d DID="F111" Desc="ECU Core Assembly Number" Data="DS7T-14G025-EK"/>
<d DID="F113" Desc="ECU Delivery Assembly Number" Data="DU5A-17E678-EL"/>
<d DID="F120" Desc="ECU Software #2 Part Number" Data="FT4T-14G082-HD"/>
<d DID="F162" Desc="Software Download Specification Version" Data=""/>
<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
<d DID="F16B" Desc="ECU Cal-Config #2 Part Number" Data="FT4T-14G081-HD"/>
<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="DS7T-14G019-EH"/>
</m>

This is my best guess for the VBF-Loader, based on this data and my Downloads-folder:

VBF_IPMA.PNG

Problem solved: After confirming the correct files, an attempt to update via the VBF-loader failed, when it came to the 15MB-file. I loaded the 15MB-file then separatly in a second run of the VBF and it worked. Forced programming of DEAD-module was not used.

[Diamondear]

I have the same problem with the Update Wizard UCDS Adapter v3 Software v.2.0.003.001.
Module Update failed.

IMAG1626-2.jpg

Later I followed the advice of @Crouser

VBF-Loader, based on this data and my Downloads-folder:

<m module="IPMA">
<d DID="F10A" Desc="ECU Cal-Config Part Number" Data="FS7T-14G024-SF"/>
<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-FU5A-17E678-SD"/>
<d DID="F111" Desc="ECU Core Assembly Number" Data="FS7T-14G025-SG"/>
<d DID="F113" Desc="ECU Delivery Assembly Number" Data="FU5A-17E678-SG"/>
<d DID="F120" Desc="ECU Software #2 Part Number" Data="FT4T-14G082-ME"/>
<d DID="F162" Desc="Software Download Specification Version" Data=""/>
<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
<d DID="F16B" Desc="ECU Cal-Config #2 Part Number" Data="FT4T-14G081-ME"/>
<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="FS7T-14G019-SG"/>
</m>

IMAG1627-2.jpg

When it comes to he last 15M file is not loaded and I can not stop the procedure successfully.

Screenshot 2017-11-24 09.17.07.png

It also stops blocking the file 15M.

I also tried with Ford IDS with the New Programming Module procedure, but I receive from Ford corrupt data for initial module initialization (As-Built).
Ford IDS does not even accept manual upload of AS-Built data in the IPM-A module.

Now my car is without the working IPMA module, waiting to solve somehow.

First DTC Pool
----------------------------------------
Module Name: IPMA
F10A - ECU Cal-Config Part Number : FS7T-14G024-SF -> Missing
F110 - On-line Diagnostic Database Reference Number : DS-FU5A-17E678-SD
F111 - ECU Core Assembly Number : FS7T-14G025-SG
F113 - ECU Delivery Assembly Number : FU5A-17E678-SG
F120 - ECU Software #2 Part Number : FT4T-14G082-ME
F162 - Software Download Specification Version :
F163 - Diagnostic Specification Version : 0x03
F16B - ECU Cal-Config #2 Part Number : FT4T-14G081-ME
F188 - Vehicle Manufacturer ECU Software Number : FS7T-14G019-SG -> Missing
F18C - ECU Serial Number : 0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF
----------------------------------------

After DTC Pool
----------------------------------------
Module Name: IPMA
F10A - ECU Cal-Config Part Number :
F110 - On-line Diagnostic Database Reference Number :
F111 - ECU Core Assembly Number : FS7T-14G025-SG
F113 - ECU Delivery Assembly Number : FU5A-17E678-SG
F120 - ECU Software #2 Part Number :
F162 - Software Download Specification Version : 0x05
F163 - Diagnostic Specification Version :
F16B - ECU Cal-Config #2 Part Number :
F188 - Vehicle Manufacturer ECU Software Number :
F18C - ECU Serial Number : 0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF0xFF
----------------------------------------

I can have these two calibrations?

FS7T-14G024-SF
FS7T-14G019-SG

Help help help !!!

[Diamondear]

PARTIALLY RESOLVED

I managed to unlock the IPMA module by only performing these two calibrations.

Screenshot 2017-11-25 15.24.06.png

AFTER UPDATE

<m module="IPMA">
<d DID="F10A" Desc="ECU Cal-Config Part Number" Data="FS7T-14G024-SG"/> New Calibration
<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-FU5A-17E678-SE"/>
<d DID="F111" Desc="ECU Core Assembly Number" Data="FS7T-14G025-SG"/>
<d DID="F113" Desc="ECU Delivery Assembly Number" Data="FU5A-17E678-SG"/>
<d DID="F120" Desc="ECU Software #2 Part Number" Data="FT4T-14G082-ME"/>
<d DID="F162" Desc="Software Download Specification Version" Data=""/>
<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
<d DID="F16B" Desc="ECU Cal-Config #2 Part Number" Data="FT4T-14G081-ME"/>
<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="FS7T-14G019-SH"/> New Calibration

The other two calibrations do not work:

HS7T-14G082-CB
HS7T-14G081-CB

WHY ??

Pre-collision system it's OK
Traffic Sign Recognition it's OK
Lane Keeping AID error in DTC.

Camera calibration with ForScan and Ford IDS fails.

I have a suggestion that calibrations downloaded via UCDS are incorrect.


I absolutely need these two calibrations:

FS7T-14G024-SF
FS7T-14G019-SG

[a4tech]

Hello I have 2 cameras but UCDS has an issue to write Direct Config changes to camera.

Код: Выделить всё

	<m module="IPMA">
		<d DID="F10A" Desc="ECU Cal-Config Part Number" Data="HS7T-14G024-EB"/>
		<d DID="F110" Desc="On-line Diagnostic Database Reference Number" Data="DS-FU5A-17E678-MG"/>
		<d DID="F111" Desc="ECU Core Assembly Number" Data="HS7T-14G025-EB"/>
		<d DID="F113" Desc="ECU Delivery Assembly Number" Data="HU5A-17E678-FB"/>
		<d DID="F120" Desc="ECU Software #2 Part Number" Data="HS7T-14G082-EB"/>
		<d DID="F162" Desc="Software Download Specification Version" Data=""/>
		<d DID="F163" Desc="Diagnostic Specification Version" Data="0x03"/>
		<d DID="F16B" Desc="ECU Cal-Config #2 Part Number" Data="HS7T-14G081-EB"/>
		<d DID="F188" Desc="Vehicle Manufacturer ECU Software Number" Data="HS7T-14G019-EB"/>
	</m>

and 2nd one:

Код: Выделить всё

<NODEID>706
<F10A>FT4T-14G024-AG</F10A>
<F110>DSFU5A-17E678-DH</F110>
<F111>FT4T-14G025-AF</F111>
<F113>FU5A-17E678-AF</F113>
<F120>FL3T-14G082-DE</F120>
<F16B>FL3T-14G081-DE</F16B>
<F188>FL3T-14G019-DF</F188>
</NODEID>

Those calibrations are not supported by UCDS and anything from DC can not be write to the module. In addition Traffic Signs Recognition does not works. Line assist is fine.

[a4tech]

Did You manage an success update ?

I can not get into Direct Config for my IPMA and Turn on Traffic Signs Recognition. I have Line Assist and Auto High Beam which works perfectly but I want to add TSR.

Reading DC is fine. Write -> Error.

[Andy232]

Hi

I Have a Problem with Update my IPMA. I have Update IPMA with updatewizzard.
the wizzard loads the 14G019 and 14G024 perfekt but stops with error on 14G082. and kills the module.
the i have use the VBF loader for DEAD modules
SBL / 14G019 / 14G024 / 14G081 / 14G082
it works also 14G019 / 14G024 and breaks the 100% 14G081
this was with version 2.0.003.005
now with version 2.0.003.007
i have testet the same.
whe i only load the 14G019 and 14G024
the IPMA talks with the car but the Traffic Sign / Lane Keep and Warn and the Automatic higbeam does not work.
but then i load 14G081 or 14G082 alway the system load 100% but he say Flash Fail
I have flash on HS2

My Original Software was DS7T-14G019-EJ DS7T-14G024-EF FT4T-14G081-HE FT4T-14G082-HE

My Car is an Mondeo 2015 TDCi 155KW 210HP Titanium
My Laptop is a Dell Latitude Core i7 16GB Ram 512GB SSD Win10 Enterprise 64Bit (1703)
UCDS S/N: 2A4D81BA1100000000000000000AD H/W ver.: 4.0 / F/W ver.: 11.00

How can I do to flash all and the system works 100% ?
Thanks Andy

[Diamondear]

Hi,
someone has already tried to update this IPMA module with the new version of UCDS v2.0.004.003. ??
Currently I have the module FU5A-17E678-SH with calibration FS7T-14G019SH.
UCDS Update Wizard notifies the presence of two updates.
The first update with the FUSA-17E678-SJ calibration level finds all the packages present.
while
on the second update with calibration level FUSA-17E678-SK does not find the FS7T-14G24SJ package.

Is it possible to receive it or enter it in the Calibration Server?

[zaga1977@gmail.com]

Good morning My module IPMA DU5A-17E678-EM after Wizard update with UCDS 2.00007.017 is dead !
I have read all topic but when I force module with Loader the installation don't work also if I separed installation, this is in photo the error, please help me ! Thx
@Diamondear where are you?????
SOLVED: OPTION WHITH "HS" ACTIVE, THX