17 Fusion Sport SBL/Cal Files

Welcome...

Модератор: DanMc85

Ответить
17FusionDriver
Сообщения: 5
Зарегистрирован: 16 мар 2019, 02:20

17 Fusion Sport SBL/Cal Files

Сообщение 17FusionDriver »

I know this is asking a lot but is there anyone who can at least give me the list of original SBL and calibration/software files for the PCM for my car? VIN is 3FA6P0VP4HR198918. Think this is all due to a bad flash to the PCM because I took an update that was for a Mondeo, now the module is listed, but has a red X in Update Wizard telling me no update available. My DTCs all seem to point to it.

I would also like to know what the original SBL files are for the following modules: ACM, DDM, DSM, DSP, FCIM, GSM, IPMA, PDM, RCM, SCCM, TCRM, TCU

I know I can see these under Update Wizard to some extent, but I don't trust it.

Also, will I have to go to Direct Configuration and load the data for the PCM after flash from FordEtis and write to the module?

Аватара пользователя
kroligoff
Сообщения: 1496
Зарегистрирован: 16 янв 2013, 11:38

Re: 17 Fusion Sport SBL/Cal Files

Сообщение kroligoff »

Select in Update Wizard Fusion 17MY

17FusionDriver
Сообщения: 5
Зарегистрирован: 16 мар 2019, 02:20

Re: 17 Fusion Sport SBL/Cal Files

Сообщение 17FusionDriver »

That's the issue. Update Wizard has a red X beside the PCM and is not allowing me to flash the stock PCM software back to it. I know I can use VBF File Loader to flash the PCM back to stock, but I need to know what files I need. I have been told the PCM's SBL file is DL3A-14C273-AC.VBF and the stock ECU Software (according to FordETIS) is HS7A-14C204-BBG. Are these the only files I need for VBF File Loader to flash the PCM? At this point, I've figured out everything else. Thanks!

Oh, do I use HS3 to flash this software in VBF File Loader?

17FusionDriver
Сообщения: 5
Зарегистрирован: 16 мар 2019, 02:20

Re: 17 Fusion Sport SBL/Cal Files

Сообщение 17FusionDriver »

So today I attempted to use VBF loader on the PCM. I used DL3A-14C273-AC.VBF as my SBL and HS7A-14C204-BBG as my stock software file that is in accordance with Ford ETIS. Upon choosing Fusion (CD391) <2013, then Sleep All Modules and using various networks like MS_CAN, HS1 and HS3 it would not flash, giving the same result each time. After clicking the Program button at the bottom it posts the following:

00:00:00:713: HW part number: HS7A-12A650-AZB
00:00:00:716: Loading and prepare database...
00:00:03:200: Detected module: PCM
00:00:03:348: Searching for SEED keys...
00:00:10:215: SEED Keys found.
00:00:10:218: Prepare "Sleep all modules" to CAN_HS
00:00:13:780: Programming mode OK!
00:00:14:784: Requesting protected mode...
00:00:14:900: Unknown type of module...No SEED KEY found in base...

I'm not sure what's going on here. All my other modules flashed back to my stock software without issue in VBF Loader. Can anyone assist?

ETIS Info:
ModulesFordETIS23APR19.jpg
У вас нет необходимых прав для просмотра вложений в этом сообщении.

Аватара пользователя
kroligoff
Сообщения: 1496
Зарегистрирован: 16 янв 2013, 11:38

Re: 17 Fusion Sport SBL/Cal Files

Сообщение kroligoff »

Use checkbox and Input manual hw part: HS7A-12A650-BBG

17FusionDriver
Сообщения: 5
Зарегистрирован: 16 мар 2019, 02:20

Re: 17 Fusion Sport SBL/Cal Files

Сообщение 17FusionDriver »

kroligoff писал(а):Use checkbox and Input manual hw part: HS7A-12A650-BBG
Which box are you referring to? The actual hw part number of the module is HS7A-12A650-AZB though according to FordETIS and UCDS?

Ответить